- Hp 1055 Service Manual
- Service Manual Troy-bilt
- Manual Car Service Manuals
- Hp 1055 Driver Download
- Service Manual Laptop
- Printer Hp Deskjet 1055
- Hp 1055 Paper
- Automotive Repair Manuals
- Sub-Systems Manuals
- Automotive Tools
- A/C Service
- Electrical Service
- Engine Service
- Body/Chassis Service
- Gauges/Measuring Tools
- Shop Equipment
- Brake, Tire & Wheel
- Hand Tools
- Power Tools
- Automotive Accessories
- Auto Parts
- Scanners/Readers OBD-II/I
- OTC
- Transmission Parts & Rebuild
- Heavy Truck & Bus Repair
- Repair Manuals / Scan Tools
- ASE Test Prep
- Labor Guides
- Marine Repair Manuals
- Motorcycle Repair Manuals
- Honda
- Kawasaki
- Suzuki
- Yamaha
- Scooter Repair Manuals
- ATV Repair Manuals
- High Performance Engines
- Spanish Repair Manuals
Size:Download
This is a complete service manual for the HP DesignJet 1050 & 1055CM plotters and DOWNLOAD. Service Calibrations HP DesignJets 1050C and 1055CM Printers Service Manual 5-3 Service Calibrations The following is a list of all internal service calibrations available in. Manuals or user guides for your HP Deskjet 1055 All-in-One Printer - J410e. Event Automation Service. View and Download HP DesignJet 1050C and 1055CMs instruction manual online. Manual Service Printers 1055CM and 1050C DesignJets HP. HP-GL/2 Config, Service. Find HP Designjet 1050C 1055CM repair parts and accessories online at LPS Computer! Shop today for all needed replacement supplies and get fast shipping!
12Next >< Back= Page 3 =345678910111213141516171819202122>>>
Troubleshooting
Problems with the Vacuum Fan
If you have problems loading either Roll or Sheet Media, then there could be a problem with the Vacuum Fan. To verify if there really is a problem with the Vacuum Fan, try the following:
1With the Printer ON, open the Window of the Printer and place a sheet of HP High Gloss Photo Paper (must be D-Size), aligned with the blue lines on the Center Platen. If the Vacuum Fan holds the sheet in place, and then loads it correctly, then the Vacuum Fan functions correctly. If the Vacuum Fan does not hold the sheet in place (no suction), then try the following:
n Check that the holes in the Center Platen are NOT blocked.n Check that the Vacuum Fan is installed correctly.
n Replace the Vacuum FanÞ Page8-11.
2If the Vacuum Fan held the sheet in place, but couldn’t correctly
load it, then there could be a problem with the Overdrive. In this case, replace the Platen Assembly Þ Page8-63.
Vacuum suction much lower at high altitudes
At altitudes above 3,000 meters, the vacuum force holding down the media will be lower, therefore the media will not be held in place properly causing:
nInk Smearing on the Media.
nPrinthead crashes against the Media.
nCut Sheet loading problems (high probability).
nRoll Media loading problems (low probability).
PRINTER LIMITATION - NO SOLUTION AVAILABLE.
Bin marks on prints done on HP High Gloss media
Prints done on HP High Gloss media are sensitive to scratches when they fall into the media bin. To solve the problem, try the following:
nAdvise the customer to install the Media Bin cover, that was included with the Printer, to avoid this problem.
nIf possible, advise the customer to hold the prints and prevent them from falling in to the bin.
HP DesignJets 1050C and 1055CM Printers Service Manual |
Troubleshooting
Printhead Crashes/Smears on High Density Prints
Using Coated Media
High density prints can cause cockle mainly on HP Coated Media. This causes two main problems:
1.Cockling in the borders - Because the printer places too much ink on the Coated Media, the borders of the print become raised, causing the Printhead to crash against the media. To solve the problem, try the following:
nCheck in the Front Panel if Ink Limiting is ON or OFF. If Ink Limiting is OFF, turn it ON.
nChange the paper margins to 15mm, either in the Front Panel or in the Driver. If the customer is printing PostScript images, send them a PPD file containing the extended margins of 15mm.
2.Cockling within the print - If the Printer places too much ink within the print, the media starts to ripple, causing the Printhead to smear against the media. To solve the problem, try the following:
nCheck in the Front Panel if Ink Limiting is ON or OFF. If Ink Limiting is OFF, turn it ON.
nNever use HP Coated Media for High Density prints. As a substitute use HP Heavy Coated Media.
Color changes when stacking prints done on HP High Gloss Media
Color differences can be seen between the covered and uncovered part of a print done on HP High Gloss Media. This is because the part of the print exposed to the air is always lighter than the covered one. The ink on the covered part of the print cannot evaporate therefore the ink continues to diffuse creating larger ink dots. To solve the problem, try the following:
nAllow the print to absolute drying completion before stacking. Depending on the ink percentage, this can take from 10 minutes up to 3 hours.
nCreating dryer environmental conditions helps reduce the problem. To find the environmental conditions, print the Service Configuration Print (Printer Setup Menu /Utilities /Test prints /
Service config)
HP DesignJets 1050C and 1055CM Printers Service Manual |
Troubleshooting
Color differences between one image printed on the HP DesignJet 1000 Series and the rest of the DesignJet platforms are due to the different chemistry of the 1000 series inks compared with the rest of the inks for other printers. This color variability among different HP DesignJet Series Printers has been always present. To solve the problem, try the following:
nPerform the color calibration from the driver at the time of printing. However, that calibration is not very accurate but it may help in the most severe cases.
nSome applications have color controls for the user to modify the image in order to obtain the desired colors.
nPrinting with PostScript reduces the problem significantly.
nAvoid very long exposures to extreme environmental conditions after printing with glossy media (more than 12 hours at 80% humidity may result in severe changes in color).
Scratches on prints done on NTP, Vellum and HP High Gloss media
Normally at the end of a roll, the curl on the media is high and the printed area can touch the media load handles or the media roll, transferring ink to the 'still-not-printed' media or damaging the actual print. This problem mainly affects Natural Tracing Paper (NTP), Vellum and HP High Gloss Media. To solve the problem, try the following:
nIncrease the Dry Time using the Front Panel (Refer to the User’s Guide - Chapter 3 Working with Paper).
Hp 1055 Service Manual
nInstall a new roll of media.
HP DesignJets 1050C and 1055CM Printers Service Manual |
Troubleshooting
Banding at variable extreme environmental conditions
Since the Accuracy Calibration has been done at normal environmental conditions, printing in extreme environmental conditions will cause banding because the advance of the Drive Roller does not correspond to the same conditions that the calibration was done in. To solve the problem, try the following:
nPerform the Accuracy Calibration in the new environmental conditions (Refer to the User’s Guide - Chapter 8 Reconfiguring your Printer).
Banding due to Ink Cartridge replacement while printing
A user has removed the Ink Cartridge while the printer was printing, which has caused the printer to stop. If the user does not replace the Ink Cartridge immediately, when the printer starts to print again, a band will appear in the position where the printing restarted. This is because the wet ink interacts with the dried ink on the media causing the band to appear. To solve the problem, try the following:
nDo NOT remove the Ink Cartridge while the Printer is Printing. Only replace/remove Ink Cartridges in between Prints.
nIf the Ink Cartridge was replaced due to the 'Empty' status on the Front Panel, then advise the customer to replace the Ink Cartridge when the 'Very Low' status is showing on the Front Panel.
Long term bleed and hue shift on HP High Gloss media
Under high humidity conditions (approx. >65%) the water trapped in the air can easily be absorbed by the highly hydrophilic media coating polymers. That allows the dye to migrate through the coating and causes bleeding. This problem is especially noticeable with the colors that require Magenta. To solve the problem, try the following:
nReduce the level of humidity (<65%) that the Printer is working in. To find the humidity level, print the Service Configuration Print (Printer Setup Menu /Utilities /Test prints /Service config).
HP DesignJets 1050C and 1055CM Printers Service Manual |
Troubleshooting
Lower image gloss directly after printing on HP High
Gloss Photo Paper
Lower gloss appearance of the print when the media is drying which gradually disappears to get the final gloss level (between 10 and 60 minutes depending on the ink density). Try the following:
n Wait at least 60 minutes to achieve the high gloss appearance.
34' Rice Paper not supported
Roll length is 34' (Non-standard) and the pinch wheels can’t control edge of media causing ink smears and Printhead crashes in middle of prints with or without area fills.
PRINTER LIMITATION - NO SOLUTION AVAILABLE.
Cut Sheet rice paper loading failure
Thin rice paper is sucked into the Center Platen grooves and Linear Blade Ridge. This implies that the friction between the Center Platen and the rice paper becomes higher than between the Overdrive wheels and the paper. This effect make it almost impossible to load the rice paper correctly because the Vacuum is too high.
PRINTER LIMITATION - NO SOLUTION AVAILABLE.
Worm marks on HP Coated media with light area fills
Light bands (S-shaped) in Paper axis direction where light area fills are printed, causing unacceptable Image Quality defect.
nPrint the Service Configuration Print (Þ Page1-19) and check if the level of Humidity is very low (below 30%). Increasing humidity may help in reducing the severity of the problem.
NOTE | The media is causing the problem and NOT the Printer. Do not |
attempt to try and replace Printer parts to solve this problem. |
HP DesignJets 1050C and 1055CM Printers Service Manual |
Troubleshooting
Solving | |
The Front Panel Keeps Indicating that Media Is Misaligned or | |
Incorrectly Positioned | |
Roll media | n The roll may be loaded the wrong way. The paper should load |
over the roll toward you. | |
n The paper may be loaded at an angle. The | |
be parallel to the white line on the paper entry roller. | |
Ensure that the paper is wrapped tightly on the roll. This is a | |
WARNING | |
very important step to remember because if this is not done, the | |
media may be loaded at an angle, causing the media to be | |
rejected. | |
n Perform the manual alignment procedure (Refer to the User’s | |
Guide). | |
n Check that the paper is correctly loaded onto the spindle. | |
Sheet media | n It must be loaded with the |
perforated line on the printer. | |
n The media may be crumpled or warped or may have irregular | |
edges. | |
n If you are using | |
angle or they may be rough. Do not use | |
purchased sheet media. | |
n If the media you are trying to load is very slippery, hold the | |
media with both hands, and gently push the media into the printer | |
until it buckles upwards in the middle, this will help the printer to | |
load it. | |
n If the overdrive is covered in dust, it will have problems picking | |
up the sheet media during the load process. Clean the Overdrive | |
using the Overdrive Cleaning Service Utility Þ Page |
HP DesignJets 1050C and 1055CM Printers Service Manual |
Manual Service Printers 1055CM and 1050C DesignJets HP
Queuing & Nesting | Queuing Management | O. K. | Copies |
Queue | On, Off | Statistics | |
Nest | Off | Move to top, | |
Delete page | |||
In order, Optimal | 99 .. 2, 1 min |
Size
Rotate
Margins
Nest Spacing
Mirroring
@
PostScript Scale
Inked Area, Software etc
Oversize
ARCH
JIS
ANSI
ISO
TOYO,0 .. 270
SWOP, Native
Normal, Extended
On, Off
On, Off
@
100% .. 419% Fit to Page
99 .. 1, 0
Width, Length
Over A2, Over A1
Statistics
Best ARCH,
ARCH A .. E1
Best JIS B,
JIS B4 .. B1
Best ANSI,
ANSI A .. E
Best ISO A,
ISO A4 .. A0
Automatic
Manual | 30..5 |
Menu | Troubleshooting |
Service Manual Troy-bilt
Manual Service Printers 1055CM and 1050C DesignJets HP
Troubleshooting
Palette | Software, Factory, | |||
Palette A, Palette B | ||||
Define palette | Palette A, | Pen Number 0 .. 15 | Width | 0.13 mm - 12.0 mm |
Palette B | ||||
Factory | Pen Number 0 .. 15 | Color | 255 .. 1, 0 | |
Merging | Off, On |
@ | @ |
Ink Emulation | TOYO, EuroScale |
SWOP, Native | |
@ | @ |
Color Calib., | Off, On |
Ink Limiting |
Manual Car Service Manuals
Manual Service Printers 1055CM and 1050C DesignJets HP
Cutter
Lang
Drying time
Page Accuracy
Network ID
Network Card
I/O Timeout
On, Off
7586, HP-GL/2
Hp 1055 Driver Download
CALS/G4
@
PostScript,
Automatic
Automatic,
None
Manual
Optimized
Maximum
Service Manual Laptop
DNS Name,
Appletalk, IP Address
![1055 1055](https://www.her.my/image/cache/catalog/multi2/2016/10/1a53-550x550.jpg)
HW Address
Configuration
Printer Hp Deskjet 1055
Terminator | Normal, Special |
255 .. 2, 1 min
JetDirect Menu
See the Setup Guide
Troubleshooting
Hp 1055 Paper
Troubleshooting
Create pattern, | Measure pattern |
Restore Factory | Recalibrate |
Up, Down | RAM present, Hard disk, Code Rev | @ PostScript Code Rev, PostScript Font Rev | PrintheadOff,alignmentOn | Accuracy | Short, Full |
printheads, | menu, | data | OnOff, | ||||||||
Displaycontrast | Statistics | Menu, | Menu, | Samples | Testprints | Menumode | |||||
Recover | Default | Palette, | |||||||||
Palette, | Samples Display | Calibration |
Utilities
enu, ples Malette, am S P | @ onts Fcript ostSP |
Demosemos
HP DesignJets 1050C and 1055CM Printers Service Manual |
12Next >< Back= Page 3 =345678910111213141516171819202122>>>